Balance a closed polygon’s interior angles before computing coordinates
Convert a five-station angular excess to arcseconds and distribute it under an explicit equal-weight assumption.
Five stations · measured 540°00′25″ · excess +25″On this page
Establish the angular figure you actually observedAllocate the correction in one unitCheck how the corrections propagate into bearingsKeep angular and linear closure visible separatelyFive turns add to 540°00′25″. The lengths have yet to enter the calculation, but the angles already disagree by 25″. This is an opportunity to catch an observation or transcription problem before computing any latitudes, departures or adjusted coordinates.
Establish the angular figure you actually observed
A simple, closed, five-sided polygon in a plane has an interior-angle sum of (5 − 2) × 180° = 540°. Each observation in this example represents the interior angle between the incoming and outgoing sides. If the field book contains angles right that run around the outside, reduce them to the intended interior angles first. An open traverse needs an orientation check against a known terminal direction and uses a different condition.
These demonstration angles have similar observation procedures and are assigned equal weight for the example.
| Station | Observed interior | Equal correction | Adjusted interior |
|---|---|---|---|
| A | 100°12′10″ | −5″ | 100°12′05″ |
| B | 115°20′15″ | −5″ | 115°20′10″ |
| C | 97°04′20″ | −5″ | 97°04′15″ |
| D | 112°18′25″ | −5″ | 112°18′20″ |
| E | 115°05′15″ | −5″ | 115°05′10″ |
For an independent addition, sum the observed columns separately. Degrees total 539, minutes total 59, seconds total 85. Carry 60 seconds into one minute, then 60 minutes into one degree. The total is 540°00′25″. Treating the fields as base-ten digits would produce a convincing but entirely different total.
Allocate the correction in one unit
The signed excess is observed minus required, or +25″. The total correction must be −25″. Dividing by five equivalent observations gives −5″ per angle. Once applied, the adjusted seconds sum to 60, producing exactly the extra minute required to bring 539°59′ to 540°.
Store observations, corrections and adjusted angles in separate columns. For a spreadsheet, calculate internally in seconds or decimal degrees. Convert to degrees, minutes and seconds for display. If one correction crosses a minute boundary, the internal representation distributes the borrow naturally. Manual subtraction from a printed seconds field needs an explicit borrow.
Check how the corrections propagate into bearings
Start with a known forward bearing for a side of the polygon. At the next station first form the backsight direction. Turn from that backsight to the next leg using the observed sense of rotation. Apply the same convention at each station. Using a plan sketch to identify which side of each line is inside the polygon helps avoid choosing a reflex angle.
Equal corrections to interior angles do not give identical corrections to every forward bearing. Each newly computed bearing inherits the changes accumulated upstream. At the end, the carried direction should return to the starting orientation modulo 360°. An angular-sum check can still pass if two station angles were interchanged. A bearing check against an independent line is therefore especially valuable.
Keep angular and linear closure visible separately
The length observations have not changed anywhere in this example. Once the directions are carried, reduce the measured horizontal lengths to coordinate components and compute the endpoint residual. The loop calculator takes bearings or azimuths and distances, so enter the resulting absolute directions there, rather than entering interior angles in its bearing field.
For an actual adjustment, confirm the observations meet the project’s acceptance rules before distributing the discrepancy. A setup with a very short backsight or a different observation procedure might have a different weight, and omitted or reversed angles need investigation. An equal-share correction is justified here by the stated training assumption. Preserve that assumption in the report alongside the original 25″ discrepancy, even after the adjusted sum prints exactly 540°.
As a final hand check, subtract the first four adjusted angles from 540° and compare the remainder with E. The result should be 115°05′10″. This checks the fifth row without repeating the same five-term summation.