Traverse DeskGet COGO
Coordinate geometry

Use the chord of a circular course to check endpoint closure

Use a 60° arc and a 50 m radius to distinguish arc travel, straight chord displacement and the area omitted by a chord-only plot.

Worked exampleRadius 50 m · central angle 60° · chord 50 m
On this pageReconstruct the curve from two elementsDetermine the chord bearing from the tangentMake a straight-course endpoint testLabel the consequences on the report

A record calls for a 52.360 m arc. Typing that number as a straight distance creates a 2.360 m discrepancy even when every recorded element agrees. A straight-course calculator needs the displacement between the endpoints. Along a circular curve, the distance traveled around the circumference is greater than the length of that displacement.

Reconstruct the curve from two elements

Consider a simple circular arc with radius 50 m and central angle 60°. Convert the angle to π/3 radians. The arc length is radius times central angle in radians, or 50 × π/3 = 52.359878 m. The long chord is 2R sin(Δ/2) = 100 sin(30°) = 50.000 m.

The arc length and long chord refer to exactly the same endpoints. They answer different questions. The arc length advances the chainage along the curved alignment. The chord length and chord bearing locate the end relative to the start. A radius, central angle and arc length alone do not establish the curve’s orientation on the sheet.

Determine the chord bearing from the tangent

Suppose the tangent at the beginning points due north and the arc turns right through 60°. The tangent turns toward the east. For this simple arc the long chord points halfway between the tangent directions, at an azimuth of 30°. Its north displacement is 50 cos 30° = 43.301270 m. Its east displacement is 50 sin 30° = 25.000000 m.

Use the radius as an independent construction. Starting from local N 0, E 0, the center of a right-hand curve is 50 m east, at N 0, E 50. The distance from that center to the computed end at N 43.301270, E 25 is √(43.301270² + 25²), again 50 m. A sign error in the curvature direction would put the endpoint on the other side of the initial tangent.

Make a straight-course endpoint test

Enter the following three lines in the closure calculator with metres selected. The second and third lines return by orthogonal straight courses.

30, 50
180, 43.301270
270, 25

The gap is below a micrometre with the displayed precision. Replace the first distance with 52.359878 while retaining azimuth 30°. The extra 2.359878 m projects along the chord direction and produces a gap of approximately that length. This is a useful fingerprint for the arc-as-chord error, provided the curve’s orientation and other calls have been checked.

Label the consequences on the report

A chord-only polygon has the correct arc endpoints, yet its boundary between those endpoints is straight. Its perimeter understates the actual traveled curved boundary by about 2.359878 m in this example. A relative precision based on the chord-only traverse length will consequently use a different denominator from one derived from the actual boundary length.

An area inferred from the chord-only sketch also omits the circular segment. For this minor arc the segment area equals R²(Δ − sin Δ)/2 with Δ in radians. Here it is about 226.465 m². Whether to add or subtract that segment from a larger parcel calculation depends on the direction traveled and which side is inside. Preserve the true arc geometry for area or deliverable drafting.

If the record gives a compound, reverse, spiral or non-tangent curve, reconstruct its actual elements instead of applying the simple tangent-and-half-angle shortcut. In your closure worksheet, mark the chord as a construction and retain the original arc description beside it. A CAD technician receiving the file then knows why a numerically closed polyline still needs its curved course restored.

If the CAD file supplies both a long-chord bearing and an initial tangent bearing, compare their separation with half the stated central angle. In this example 30° separates them. That quick angular comparison often reveals a curve described from the opposite end, even when both files agree on radius and arc length.

References

Check traverses offline with COGO